Yes.
The HORIZON 30 Series supports HDMI eARC (HDMI 1 port), allowing high-quality audio output to compatible AV receivers and soundbars.
Connect using HDMI eARC
1. Connect the HDMI 1 (eARC) on the projector to the HDMI ARC/eARC port on your AV receiver.
2. Press the Settings button on the remote to open Quick Settings, then select All Settings.
3. Go to: Display & Sound > Audio Output.
4. Set Audio Output Device to HDMI ARC/eARC.
5. Configure Digital Output as needed:
- Auto: Automatically selects the optimal output format based on the capabilities of the connected device.
- Bypass: Outputs the signal in its original compressed form without decoding it. By decoding the signal using an external amplifier or similar device, you can enjoy surround sound formats such as Dolby or DTS.
- PCM: Converts audio into uncompressed digital audio for output. This format offers the highest compatibility and can be played back on a wide range of devices.
- Dolby Digital Plus: Outputs audio in the Dolby Digital Plus (E-AC-3) format. It is more efficient than standard Dolby Digital and allows for higher-quality transmission.
- Dolby Digital: Outputs audio as compressed surround sound in the Dolby Digital (AC-3) format.
- MAT: A method for transmitting Dolby audio via HDMI. It transmits signals by adding metadata to a PCM stream.
6. On your AV receiver, ensure the input source is set to receive audio via ARC/eARC.
Notes
- For the best eARC performance, use a certified Ultra High Speed HDMI Cable (HDMI 2.1).
- On the projector, go to Settings > Display & Sound > Sound > eARC, then set eARC to Auto.
- Make sure your AV receiver supports HDMI eARC.
- On most AV receivers, the ARC/eARC port is located in the HDMI OUT section.
- If the port is not labeled ARC or eARC, refer to your AV receiver's documentation or contact the manufacturer to confirm compatibility.
The HORIZON 30 Series supports HDMI eARC (HDMI 1 port), allowing high-quality audio output to compatible AV receivers and soundbars.
Connect using HDMI eARC
1. Connect the HDMI 1 (eARC) on the projector to the HDMI ARC/eARC port on your AV receiver.
2. Press the Settings button on the remote to open Quick Settings, then select All Settings.
3. Go to: Display & Sound > Audio Output.
4. Set Audio Output Device to HDMI ARC/eARC.
5. Configure Digital Output as needed:
- Auto: Automatically selects the optimal output format based on the capabilities of the connected device.
- Bypass: Outputs the signal in its original compressed form without decoding it. By decoding the signal using an external amplifier or similar device, you can enjoy surround sound formats such as Dolby or DTS.
- PCM: Converts audio into uncompressed digital audio for output. This format offers the highest compatibility and can be played back on a wide range of devices.
- Dolby Digital Plus: Outputs audio in the Dolby Digital Plus (E-AC-3) format. It is more efficient than standard Dolby Digital and allows for higher-quality transmission.
- Dolby Digital: Outputs audio as compressed surround sound in the Dolby Digital (AC-3) format.
- MAT: A method for transmitting Dolby audio via HDMI. It transmits signals by adding metadata to a PCM stream.
6. On your AV receiver, ensure the input source is set to receive audio via ARC/eARC.
Notes
- For the best eARC performance, use a certified Ultra High Speed HDMI Cable (HDMI 2.1).
- On the projector, go to Settings > Display & Sound > Sound > eARC, then set eARC to Auto.
- Make sure your AV receiver supports HDMI eARC.
- On most AV receivers, the ARC/eARC port is located in the HDMI OUT section.
- If the port is not labeled ARC or eARC, refer to your AV receiver's documentation or contact the manufacturer to confirm compatibility.